热线:15064011858
        13245313178
        0531-88275058
关键词搜索: 济南包装箱厂,济南手提袋,济南礼品盒,济南纸箱厂

手提袋定做厂家教您三分钟了解手提袋印刷的注意事项?

来源:http://www.liufangshun.com 时间:2021-02-20 10:16:21 发布人:六方顺 浏览量:

手提袋印刷是印刷行业的主要发展方向。尽管生产过程非常简单,但仍有许多细节需要注意。下面济南手提袋定做厂家给您带来详细的资讯。

Bag printing is the main development direction of printing industry. Although the production process is very simple, there are still many details to pay attention to. The following Jinan handbag manufacturers to bring you detailed information.

1.在手提袋印刷过程中,要注意使用相同类型的墨水,请勿混合使用不同性质的墨水,如果两者不兼容,则会影响手提袋的质量。

1. In the process of bag printing, pay attention to use the same type of ink, do not mix different types of ink, if the two are not compatible, the quality of bag will be affected.

2.打印时,请确保墨水的性质,避免阳光直射,并保持室内温度在10-26摄氏度以内。

2. When printing, please ensure the nature of the ink, avoid direct sunlight, and keep the indoor temperature within 10-26 ℃.

3.在手提袋印刷过程中,如果不定期搅拌墨水,很容易粘住,这会影响手提袋的整体外观。但请注意不要将其稀释得太多,因为印刷产品会产生色差,可以添加增稠剂以适当调整它。

3. In the printing process of the bag, if the ink is not stirred regularly, it is easy to stick, which will affect the overall appearance of the bag. But please be careful not to dilute it too much, because printing products will produce color difference, thickening agent can be added to adjust it properly.

                           手提袋定做厂家教您三分钟了解手提袋印刷的注意事项?(图1)

4.在印刷过程中,还必须充分发挥水的作用,既可以有效地控制油墨的粘度,又可以平衡pH值。如果发现ph值未控制在8.5至9.5之间,则应通过添加水或pH稳定剂进行调节。

4. In the printing process, we must give full play to the role of water, which can effectively control the viscosity of the ink and balance the pH value. If it is found that the pH value is not controlled between 8.5 and 9.5, it should be adjusted by adding water or pH stabilizer.

5.手提袋是一种高速印刷,印刷过程非常快,因此对油墨的干燥度有一定要求。如果墨水的干燥速度太慢,则可以添加干燥剂以提高其干燥速度。 如果在墨水仍不干时进行打印,则很容易使版面变脏,这也会影响整体打印效率。

5. Handbag is a kind of high-speed printing, the printing process is very fast, so there are certain requirements for the dryness of ink. If the ink drying speed is too slow, you can add desiccant to improve its drying speed. If you print when the ink is still not dry, it is easy to make the layout dirty, which will also affect the overall printing efficiency.

6.打印完成后,应清洁设备。当设备上的墨水仍处于粘性状态时,应清洁它,以提高清洁速度。如果不能用水清洗,则可以适当添加一些清洗剂。

6. Clean the equipment after printing. When the ink on the device is still sticky, it should be cleaned to improve the cleaning speed. If it cannot be cleaned with water, some cleaning agents can be added appropriately.

希望以上关于济南手提袋的内容对您有所帮助,感谢您的阅读。

I hope the above contents about Jinan handbag are helpful to you. Thank you for your reading.